what a transformation !!!!

[handsomejackuk]

Hi,

just performed the swap the clipons over trick what a transformation. rider position is about two inches higher. still have full lock on bars much more comfy.

for anyone having problems with riding position i would highly recommend this, can't believe i have had my bike nearly 9 years and didnt know about this trick.

Thanks to the inventor....

Alun

[AHTHUD]

Isn't it a bit confusing having the Throttle on the wrong side

[handsomejackuk]

takes a bit of geting used to but i find it a lot easier having the throttle the same side as clutch....

Alun

[cobbadiggabuddyblooo]

So did you change the gear lever over in foot brake lever over in unison... great if you had a stroke...lol

[arrivisto]

.. the swap the clipons over trick ...

Please enlighten me! What is this trick?

[handsomejackuk]

Hi,

did not know this trick, had my bike nearly nine years.

the trick is swap the left hand clipon for the right hand clip on, and you instantly have a raised riding position. Because normally the clipons are angled down, by swapping thme over you get the riding position raised up by about 3 inches much improved riding position, give it a try if you are having comfort issues i.e. back ache, aching wrists, been out on mine all day today and no aches or pains...

Hope this helps...

there are some pics on the forum somewhere#

Alun

[HolerTogni]

Hi handsome!

...
there are some pics on the forum somewhere#

Alun

You mean there?!

Referring greetings from Munich!

PS: Maybe this thread should be made sticky because of the great demand??

[Corners R Us]

Hi,

just performed the swap the clipons over trick what a transformation. rider position is about two inches higher. still have full lock on bars much more comfy.

for anyone having problems with riding position i would highly recommend this, can't believe i have had my bike nearly 9 years and didnt know about this trick.

Thanks to the inventor....

Alun

I'm toying with doing this to my TRX before next years pilgrimige to the Pyrenees. Do you need to drill the bars for the switchgear or is it a simple unbolt, swap over, re-install job?

Cheers, Corners

[handsomejackuk]

Hi,

just swap over.

The tubey things that attach to the clip ons come out with an allen screw. No drilig of the throttle allthat stays on the tubet hthings take no more than about 15mins. only problem i have found, is that the horn wiring is a tad short and needs re-routing as the spades seem to pull off the horn, i did squash the crimps slightly with pliers to get them a tighte fit on horn and seems to be better now.

Alun

[Corners R Us]

Hi,

just swap over.

The tubey things that attach to the clip ons come out with an allen screw. No drilig of the throttle allthat stays on the tubet hthings take no more than about 15mins. only problem i have found, is that the horn wiring is a tad short and needs re-routing as the spades seem to pull off the horn, i did squash the crimps slightly with pliers to get them a tighte fit on horn and seems to be better now.

Alun

Alun, you're a star! I'd not looked at the job properly and the bikes in the garage under a sheet at the mo. So you drop the bars/switch gear/grips off/out of the mounts, swap the mounts over then re-insert the bars into the swapped mounts without stripping the switchgear etc off them - cooool! I might do that this weekend time permitting.

I'm also undertaking a bit of a major overhaul over the winter as the valve clearances are due, I want to stubby and re-pack the cans on the bike as well as a few other jobs I have been meaning to do such as new Samco hoses all round, plugs and oil change whilst the engines stripped down. I'm planning to do all this myself with the assistance of a mechanic mates who's handy with the Snap Ons!! I must start a 'project' thread with pics....

Thanks again.

Corners the Enlightened!

[handsomejackuk]

cornrers,

yeah, real easy job. take out the silver caps on the clipons, undo the allen bolt. loosen the pinch bolt both sides left / right. loosen the clipon holding bolts... remove plastic cover first.... then simply swap over the clip on assembly.... or watever it is called !!!!


was in gloucester area last weekend.... wen to tewks/stratford/ stow/ bourton water/ chelt/ forest dean / monmouth/ home etc.... usual area abergavenny.....


will be abergav on Sunday on new bike...!!!!!


Al.....

[davamb]

Hi Alun,

I've been thinking of doing this but thought you had to cut up the fairing to get bar clearance????