Please share your secrets! What mods have you made to your TRX?
Moderators: trixynut, Mincehead, dicky, phuk72, Jak, Kevtrx849
-
OFD
- Site Sponsor
- Posts: 47
- Joined: Sun May 17, 2009 3:05 am
- Location: Kettering UK
Post
by OFD » Wed Aug 10, 2011 11:29 am
Hi
I have recently fitted a 2010 R6 rear shock with a Kayla adapter that I purchased from the "For Sale" section from Corners R Us.
What a change.
I have set it up as follows : Pre Load 4 and the damping set mid point on both as a starting point.
The ride is a lot less harsh with a lot more controll throughout the corners both on and of the gas.
I can now exit my favourite set of bends. on the B645 from Chelveston to Kimbolton, at least 10mph quicker.
So i can thououghly reccomend this mod.
Gary
Motorcycling : The best fun you can have with your clothes on....
1996 TRX. Red. Leo Vince carbon cans,FCR 41 flatsides, YZF SP front, R6 shock with Projection adapter. Polished Wheel rims, Ignitech ignition. 93rwhp.. Oh yes !!
-
biker_jay
- TRX-Enthusiast
- Posts: 125
- Joined: Sun May 18, 2008 7:10 pm
- Location: Gloucester, UK
Post
by biker_jay » Thu Aug 11, 2011 10:19 pm
Was the shock brand new? is it a yamaha item or a aftermarket one for a r6? I'm interested in doing something for my trx with the rear shock. Does it have the remote chamber?
Jay.
-
OFD
- Site Sponsor
- Posts: 47
- Joined: Sun May 17, 2009 3:05 am
- Location: Kettering UK
Post
by OFD » Mon Aug 15, 2011 7:45 pm
Hi Jay
Its a standard 2010 R6 shock. Its got a Red spring with the damping chamber incorperated into the top mount.
A lovely bit of kit, just needs one of Kayla`s adaptors to fit as its shorter than the original one.
Cheeers
Gary
Motorcycling : The best fun you can have with your clothes on....
1996 TRX. Red. Leo Vince carbon cans,FCR 41 flatsides, YZF SP front, R6 shock with Projection adapter. Polished Wheel rims, Ignitech ignition. 93rwhp.. Oh yes !!
-
biker_jay
- TRX-Enthusiast
- Posts: 125
- Joined: Sun May 18, 2008 7:10 pm
- Location: Gloucester, UK
Post
by biker_jay » Mon Aug 15, 2011 10:22 pm
Mega,
Cheers Gary.
-
fung
- Site Sponsor
- Posts: 1604
- Joined: Mon Aug 23, 2010 2:00 am
- Location: Gold Coast. South East Queensland.
Post
by fung » Tue Aug 16, 2011 4:18 am
will you please take some pics to show clearance around the top of the R6 shock when installed in your TRX.
may i ask what do you weigh?
cheers
fung
I WOULD RATHER WEAR OUT THAN RUST
-
OFD
- Site Sponsor
- Posts: 47
- Joined: Sun May 17, 2009 3:05 am
- Location: Kettering UK
Post
by OFD » Thu Aug 18, 2011 1:08 pm
Hi Fung
I weigh about 100kg fully kitted up. Photos as requested
Cheers
Gary
Motorcycling : The best fun you can have with your clothes on....
1996 TRX. Red. Leo Vince carbon cans,FCR 41 flatsides, YZF SP front, R6 shock with Projection adapter. Polished Wheel rims, Ignitech ignition. 93rwhp.. Oh yes !!
-
cal
- TRX-Enthusiast
- Posts: 652
- Joined: Wed Jul 28, 2010 11:46 pm
- Location: York
-
Contact:
Post
by cal » Thu Aug 18, 2011 6:32 pm
Nice photos there, really shows how it fits together and how neat the Kayla adapter is
, I have a question though, what are the extra holes for behind the swingarm rocker towards the rear wheel? Until I had a closer look I thought they might be for an adjustment to raise the back end, but the dont seem quite as chunky as the forward mounts and they are slightly angled/shaved at the edges. Any ideas .....anyone.....?
Cal
-
Mincehead
- TRX-Enthusiast
- Posts: 6345
- Joined: Sun Jan 25, 2009 1:40 pm
- Location: West Sussex
-
Contact:
Post
by Mincehead » Thu Aug 18, 2011 7:21 pm
It`s been asked before Cal and no-one is too sure but it could be something to do with Yamaha`s factory jig / machining centre that uitlises them.
Best ignored, the headferk isn`t worth it!
LOUD PIPES SAVE LIVES
-
biker_jay
- TRX-Enthusiast
- Posts: 125
- Joined: Sun May 18, 2008 7:10 pm
- Location: Gloucester, UK
Post
by biker_jay » Thu Aug 18, 2011 7:34 pm
Could be useful if popping the shock out for a few days, you could pop a bar in there so the back end doesn't collapse. Not official though
-
fung
- Site Sponsor
- Posts: 1604
- Joined: Mon Aug 23, 2010 2:00 am
- Location: Gold Coast. South East Queensland.
Post
by fung » Thu Aug 18, 2011 9:52 pm
thanx for these great pix.
does the shock have any identifying numbers?
now all i need is Kayla to tell me if her dogbones work well with the R6 shock and then i know what i want for christmas !!
cheers
fung
I WOULD RATHER WEAR OUT THAN RUST
-
Kayla
- Site Sponsor
- Posts: 1670
- Joined: Fri Jul 04, 2008 7:49 am
- Location: County Durham
Post
by Kayla » Fri Aug 19, 2011 8:49 am
fung wrote:thanx for these great pix.
does the shock have any identifying numbers?
now all i need is Kayla to tell me if her dogbones work well with the R6 shock and then i know what i want for christmas !!
cheers
fung
They'll work with the R6 shock, but I can't say if they work well or not- it's subjective!
I had +20mm on my bike with an R6 shock and loved it, I've got one in my 4/6, and I'll be removing the standard SZR swingarm and using a 3TJ arm so I can use an R6 shock in that too
Just because you're breathing, it doesn't mean you're alive.
-
boogie_de
- TRX-Enthusiast
- Posts: 30
- Joined: Sat Oct 16, 2010 11:29 pm
- Location: Bad Birnbach/Germany
-
Contact:
Post
by boogie_de » Fri Aug 19, 2011 5:54 pm
I've fitted my TRX with a R6 rear shock and an adapter from Kayla.
It was the best mod i've made, except the flatsides !!
No torn tire, very smooth damping, very good feedback.
The One with the Terminator leg !!
